SITE QUALITY METROLOGY PROFESSIONAL

Plastic Omnium

  • 湖北省武汉市
  • 长期
  • 全职
  • 20天前
JOB TITLEJOB FAMILYDATEMetrology EngineerQUALITY01/06/2020MANAGER TITLE (solid line)FUNCTIONAL MANAGER TITLE (dotted line)Quality Engineer leaderMISSIONIn one or two sentences, outline the primary purpose(s) of this position within the organizationAssure the assistance of Product/ Process development during trials and industrialization processes.Contribute for inspections of prototypes parts for External and Internal (QCPT) deliveries.Assist Plant Quality in factory where trials and productions are located in order to validate.Product/Process including trainings and know-how transfer.Be able to support other Clusters if necessary.Respect the department quality procedure.Alert in case of non-conformities or abnormal situation.Accuracy and reliability of data.Responsibilities & ActivitiesOutline the key areas of responsibility for this position, including the related activities and eventual authorities
  • He/she have authority to stop machines in case of immediate risk.
  • Consciously accept safety training, actively participate in safety activities and comply with safety regulations.
  • Report unsafe status and behaviors in time, and actively participate in safety improvement.
  • Must comply with all safety rules and regulations.
  • Participate to preparation of trial (parts needed, CAD/drawings, gages tooling, inspections sheets…)
  • During meeting between QE and Metrology Engineer, upon QE request. Initiate the trial preparation check-list.
  • Participate to meeting (Conf call) organized by IE to prepare trial. Finalize the trial preparation checklist.
  • Implement all activities according to check list defined during preparation trial and validate iterative steps in agreement with QE until end of trial.
  • As needed, deviation waivers can be created and submitted to QE for decision (top production or not).
  • Writes, analyzes and suggests improvements through control report, shared and approved by QE before communication to team.
  • Analyses prototype quality and recommends corrective actions in case of deviation.
  • Identifies and warns on quality risks and deviations on project.
  • Facilitate Corrective Action Activities (e.g.: 8D).
  • Contribute for inspections of prototypes parts for External and Internal (QCPT) deliveries
  • Perform inspections following upon QE requests
  • As needed, deviation waivers can be created and submitted to QE for deliveries (External & Internal).
  • Participate to machine set-up of prototype parts and serial tooling ( including repeatability &
reproducibility/process capabilities studies) performed at Plants ( Dimensional and welding inspections)
  • Assist Plant Quality in factory where trials and productions are located in order to validate.
  • Product/Process including trainings and know-how transfer.
  • Perform on job trainings during trials and launch of production to ensure the hand-over of Product /Process to the plant.
  • Be able to support other Clusters if necessary.
  • Depending on the availability of other Metrology Engineer in China and Programs requests, the Metrology Engineer:
  • Can be asked by the Plant Quality Mgr. to support any factory in China. In that case, the Metrology Engineer will perform activities 1 to 3 in-situ.
Integrated Management System (IMS)Outline the key responsibilities for this position in regards of Integrated Management System (Quality, Safety, Environment)Within his/her scope of responsibility, he/she respects the standards and rules in terms of Quality, Safety and Environment contributing to the IMS process management and improvement.ORGANIZATIONPOSITION KEY INTERFACES (internal and/or external)Internal
  • Project team
  • QE team
  • PO plant quality team
  • TC LAB team
External
  • Customer (PPAP preparation - Run @ Rate or
process audits participation ...)POSITION BACK UPFill in with back-up position titles only. Back-up should be indicated for positions in charge of customer orders treatment, supplier on-time delivery, quality, production capacity, shared loading (multi-part station), lead time, inventory level, preventive maintenance, and calibration are the ones to be provided with a back-up.Quality Engineer LeaderKEY MEASURES & FINANCIAL ACCOUNTABILITYIndicate the Key Indicators used to measure the performance of the position and the financial metrics on which the role has got a direct or indirect impact (budget, sales, …)No LTA & WLTAEach person report unsafe situation and behavior to his N+1 at least 4 times per yearQCPTMeasurement in time %PROFILE REQUIREMENTSPersonal BackgroundQuality Technician level (Plastics, ERP, Physics and measurements…)Job Technical skillsGlobal definition & tolerances knowledge : read drawings and ISO system -UUse of CMM (or equivalent) - Coordinate Measuring Machine - UUse of calipers / ultra-sonic gauges/ depth gauges/ roughness/ profile projectors for Coex-TSBM - OProficient excel word (Control report) - LLanguages : English spoken and written - LJob Soft skillsAble to communicate in EnglishAbility to work in a team environmentMust have excellent organization skillsStrong computer skills including Excel, Word, Power Point, Minitab, Access, VisioTo define the Soft Skills required for the job, please refer to PO General Competencies available on Topnet.JOB DESCRIPTION APPROVALManager name & title:HR Manager name & title:HR manager WuhanEMPLOYEE ACKNOWLEDGEMENT(optional, depends on local legal requirements)Employee name :Date: Aug 15, 2025Location:Wuhan, CNJob Requisition ID: 385502

Plastic Omnium